We recently changed from vCenter server 5.5 on Windows server to v6.0 appliance.
I recreated the backup job using the new vCenter as the source for adding the VMs.
I performed a test restore of a client VM but it fails as it tries to connect to the IP address of the old vCenter
Error: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond 192.168.2.27:443
I powered up the old vCenter, even though everything has been removed from its inventory, and tried again. Now the message is:
Error: No connection could be made because the target machine actively refused it 192.168.2.27:443
I must have missed something but only articles I find are all about restoring vCenter itself or restoring a VM when vCenter is dead.
I don't have a case ID yet as I thought I'd try the community first.
-
- Influencer
- Posts: 13
- Liked: 1 time
- Joined: Mar 20, 2012 6:28 pm
- Full Name: Randy Redekopp
- Contact:
-
- Veeam Software
- Posts: 314
- Liked: 74 times
- Joined: Mar 23, 2015 11:55 am
- Full Name: Michael Cade
- Location: Cambridge, United Kingdom
- Contact:
Re: VM Restore Fails after vCenter Replaced
When you run through the restore wizard if you are picking a restore point that was taken whilst the previous 5.5 VC was in play then it would think this is the original location, you would i would expect then have to restore to a different location and choose your new appliance.
This is the wizard for instant VM recovery where this can be configured.
Similar for Full VM restore
Hope that helps.
This is the wizard for instant VM recovery where this can be configured.
Similar for Full VM restore
Hope that helps.
Regards,
Michael Cade
Global Technologist
Veeam Software
Email: Michael.Cade@Veeam.com
Twitter: @MichaelCade1
Michael Cade
Global Technologist
Veeam Software
Email: Michael.Cade@Veeam.com
Twitter: @MichaelCade1
-
- Expert
- Posts: 206
- Liked: 41 times
- Joined: Nov 01, 2017 8:52 pm
- Full Name: blake dufour
- Contact:
Re: VM Restore Fails after vCenter Replaced
it seems as though the restore point you chose would have been tied to the old vcenter server - could have been an older restore point created through the old vcenter.
-
- Influencer
- Posts: 13
- Liked: 1 time
- Joined: Mar 20, 2012 6:28 pm
- Full Name: Randy Redekopp
- Contact:
Re: VM Restore Fails after vCenter Replaced
Thanks MichaelCade.
I had thought it wouldn't matter as I picked a new Full backup assuming that should be clean of previous associations, however your suggestion worked fine and I was able to complete a test restore using the Full Restore Wizard.
I had thought it wouldn't matter as I picked a new Full backup assuming that should be clean of previous associations, however your suggestion worked fine and I was able to complete a test restore using the Full Restore Wizard.
-
- Veeam Software
- Posts: 314
- Liked: 74 times
- Joined: Mar 23, 2015 11:55 am
- Full Name: Michael Cade
- Location: Cambridge, United Kingdom
- Contact:
Re: VM Restore Fails after vCenter Replaced
Good stuff thanks for letting me know.
Regards,
Michael Cade
Global Technologist
Veeam Software
Email: Michael.Cade@Veeam.com
Twitter: @MichaelCade1
Michael Cade
Global Technologist
Veeam Software
Email: Michael.Cade@Veeam.com
Twitter: @MichaelCade1
Who is online
Users browsing this forum: Semrush [Bot] and 85 guests